Machine Attachments

Double Tool Cross Slide

• Slide has Maximum Travel of of 3-3/4″.
• The Height to The Spindle Centerline is Approximately 4-1/2″.

Compound Slide Rest

• Has a Locking Handle Located on the Back Portion of The Slide Rest
• Allowing for Easy Mounting and dismounting
• The Top Slide Has a Maximum Travel of 4-1/4″
• The bottom slide has a maximum travel of 5″
• The hardened and Group Top Slide can be Swiveled and Locked to Any
• Location in 360 degrees
• Slide Movement is Controlled by Two Easy-Reading 2-1/2″ Diameter
• Dials That are Graduated in .001″ increments
• Each .001 Increment of The Bottom slide Represents a .001″ Change in
• Diameter of The Work-piece or .0005″ of the slide.
• Each .001″ Increment of the Top Slide dial Represents a .001 movement of The Slide.

6 Station Turret

• 9″ diameter swing
• 6 position turret with 5/8″ holes
• Lever operated
• Tight, no play

Double Tool Cross Slide

• Slide has Maximum Travel of of 3-3/4″.
• The Height to The Spindle Centerline is Approximately 4-1/2″.

5-1/2″End Working Slide

• Has Maximum Travel of 5-1/2″
• Slide is Furnished with 5/8″ Straight Bore for Holding 5/8″ Diameter Round Shank Tooling
• The Height From The Bedplate to the Spindle Centerline is Approximately 4-1/2″

Compound Slide Rest

• Has a Locking Handle Located on the Back Portion of The Slide Rest Allowing for Easy Mounting and dismounting
• The Top Slide Has a Maximum Travel of 4-1/4″
• The bottom slide has a maximum travel of 5″
• The hardened and Group Top Slide can be Swiveled and Locked to Any Location in 360 degrees
• Slide Movement is Controlled by Two Easy-Reading 2-1/2″ Diameter Dials That are Graduated in .001″ increments
• Each .001 Increment of The Bottom slide Represents a .001″ Change in Diameter of The Work-piece or .0005″ of the slide.
• Each .001″ Increment of the Top Slide dial Represents a .001 movement of The Slide.

Automatic Indexing Square Turret

• Uses 3/8 Square Shank Tool Bits
• Can use 5/8″ Round Shank Tooling if a L1A is equipped as well
• The Turret can be indexed from one station to the next within.0001″

Tailstock

• Has A hardened and Ground Spindle that is graduated in 1/8″ increments
• Has a Maximum Travel of 3-1/2″
• Movement is Controlled by a Handwheel Equipped With a White Dial That is Graduated in .001″

Straight and Taper Turning Slide D13

Equipped with:

• Graduated Swivel Base that is capable of being swiveled or locked to any angle in 360 degrees
• 5/16″ Square Shank Holder
• Lever operated slide that can travel up to 1-3/4″(44.45mm)

Automatic Indexing Square Turret

• Uses 3/8 Square Shank Tool Bits
• Can use 5/8″ Round Shank Tooling if a L1A is equipped as well
• The Turret can be indexed from one station to the next within.0001″

Radius Turning Attachment

• Uses 5/16″ Square Tool Bits
• Maximum Swing over the swivel base is 3″(76.2mm) diameter
• Swivel slide can move more than 360 degrees
• Dials are graduated in .001″ increments
• Dials can be adjusted fora zero setting with a positive lock
• Height to Spindle Centerline is 5-1/2″

4 Station Square Turret

• Mounts Directly to Cross Slide
• Uses 5/8 Square Shank Tool Bits
• Turret Indexes within .0001″ and Has a Secure Locking Mechanism, Enabling Close Tolerances to be Held on the Workpiece

Quest GT 21iT Live Tooling MGA 144 CW Attachment

• Mounts to the Cross Slide and can be removed

Quest GT Fanuc 21i T control MGA 144 E3 Triple Face Working Live Tooling

• Has a short-length top plate for maximum flexibility
• Mounts on to the Cross Slide
• 6000 rpm per spindle

Conquest GT HG 52 Tapping Attachment Fanuc 18T

• Speeds can be programmed at 120,153,167 or 207 rpm
• The dimension “L” from the top of the dovetail to the spindle centerline is 1.327″